DSC PTK5507 Manuel d'installation télécharger pdf (Page 4)

Dark Text Enable/Disable

1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.

2. Select the desired text color by enabling or disabling Dark Text. (Disabling makes the text

white.)

NOTE: This feature affects only the text on the Classic (Square) But-

ton Home Page.

Changing Home Page Look:

1. Press Options, Keypad Config, Home Page.

2. Select the desired view from either classic look (square) or contemporary (rondel).

3. To exit, press the Back or Home button.

Performing a Firmware Upgrade:

1. Insert an SD card in the PTK5507 with the new firmware.

2. Press Options, Installer Menu [Installer Code], Keypad Programming, then Firmware Upgrade.

3. Select OK to perform a firmware update (if a new firmware version is available).

Enabling/Disabling Fire, Auxiliary and Panic Buttons

1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.

2. Enable/disable the desired Fire, Auxiliary and Panic buttons.

NOTE: The Fire, Auxiliary and Panic buttons are enabled by default on

the PTK5507.

Extra Power Option

The Extra Power option will increase the brightness of the display. To enable the option:

1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.

2. Enable or disable the extra power option.

NOTE: Enabling the Extra Power option will put the keypad in a

higher current mode and the keypad will draw 400 mA.

Changing Function Keys on the Home Page:

1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Home Functions.

2. Assign the desired function to the corresponding key.

3. To exit press the Back or Home button.

Adjusting Screen Time out

1. Press Options, Keypad Config, then Backlight.

2. Select appropriate time for screen time out by using the slide bar.

3. To exit, press Back or Home button.

Accessing Clean Mode

Press Options, Keypad Config, Clean Mode.

NOTE: Clean mode will time out in 30 seconds.

Keypad Enrollment

Enter keypad programming by pressing Options, Installer Menu [Installer’s Code], Keypad

Mode Prog, then [000].

[0] Partition / Slot Assignment

Keypad Programming

Enter keypad programming by pressing Options, Installer Menu [Installer’s Code], Keypad

Mode Prog, then [000].

[001]-[064] Zone Label 1 to 64

ex. For Zone 1 enter section [001], for Zone 2 enter section [002] etc. Default: “Zone 1”-“Zone 64”

[077] Second Keypad Options

Digit Option Valid Range Default

1st Partition Assignment (0=Global Keypad) 0 to 8 1 I_____I

2nd Slot Assignment 1 to 8 8 I_____I

Section Zone

Label

[001]

[064]

1 to

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I__ _ _I

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_ _ __I

Default Option ON OFF

ON I____I 1

Chime Enabled for Zone

Openings

Chime Disabled for Zone

Openings

ON I____I 2

Chime Enabled for Zone

Closings

Chime Disabled for Zone

Closings

OFF I____I 3

For Future Use

ON I____I 4

For Future Use

OFF I____I 5

For Future Use

ON I____I 6

For Future Use

ON I____I 7

For Future Use

OFF I____I 8

For Future Use

NOTE: Do not attempt to change options 3-8 in Section 077 or the

keypad may not function as desired.

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

DSC PTK5507 Manuel d'installation Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PTK5507