DSC PC1575 Manuel d'installation

INSTALLATION MANUALVersion 3.OSecurity ProductsTM• W A R N I N G •Please refer to the System Installation Manual for information on limitationsregardi

9Table 1 — List of LINKS1000 Programmer Menu MessagesMain Menu(0) Write LINKS (1) Trouble (2) Read LINKS(0) LINKS Phone # (0) LINKS Phone #(1) System

10INSTALLATIONMounting the CabinetIt is important to mount the LINKS1000 as close to the DSC / Sur-gard alarm control panel as possible.3 feet is the

11Ground ConnectionConnect the LINKS “AUX-GND” terminal to the control panel “GND” terminal. AUX- or KEYPAD BLACK and ZONECOMMON are also good ground

12DC1664LCConnect the LINKS PGMIn terminal to the PGM 9 terminal on the MEX2 module installed with the DC1664LC.A 500 ohm resistor must be connected t

13When jumper J1 is removed, this terminal will provide the output for the LINKS1000 battery trouble indicationto the control panel. The terminal will

14HOOK-UP DIAGRAM - PC1500/1550/2525/2550/3000NOTES1 An AC power supply must be dedicatedto the LINKS1000. Do not use thesecurity system's transf

15HOOK-UP DIAGRAM - PC1575/PC5010NOTES1 An AC power supply must be dedicatedto the LINKS1000. Do not use the securitysystem's transformer to powe

16HOOK-UP DIAGRAM - PC4010/PC4020/PC4020KTNOTES1 An AC power supply must be dedicated to the LINKS1000. Do not use the security system's transfor

17HOOK-UP DIAGRAM - P16LC / P1664 / DC1664LCNOTES1 An AC power supply mustbe dedicated to theLINKS1000. Do not usethe security system'stransforme

18RELOCATING THE ANTENNAUse only the Extension Kits to extend the mounting range of the antenna. Do not cut or splice theextension cable. The maximum

1CONTENTSLINKS1000 GLOSSARY OF TERMS 2INTRODUCING THE LINKS1000 3Specifications... 3HOW THE LINKS1000

19PROGRAMMING CONTROL PANELS FOR LINKS1000IMPORTANT NOTEWhen a control panel is programmed for LINKS1000, the PGM output is dedicated to LINKS communi

20NOTENOTENOTENOTENOTE: The pager format can also be used with the PC5010 if necessary.PC1500 and PC1550 Control PanelsThe DSC PC1500 or PC1550 must b

21PC2550 Control PanelThe DSC PC2550 must be equipped with software version 1.2 or later.Programming for all PC2550 software versions:Section [30] Pro

22Yes: Zone 1 enabled for LINKS supervisoryNo: Zone 1 not enabled for LINKS supervisoryNote: When this option is enabled, the PC4010/PC4020/PC4020KT w

23The following PC4010/PC4020/PC4020KT Menu Items are not used while programming telephonenumbers for LINKS operation. Do not select these items while

24Section [490]LINKS Downloading Preamble:If necessary, program section 490 with the LINKS Preamble for the Downloading.Section [703]Dialling Delay:Pr

25Sur-Gard P1664The Sur-Gard P1664 control panel must be equipped with software version 2.0 or later.Mode 22, Address [008]: System OptionsTurn ON opt

26“On Air” IndicationWhenever the LINKS unit is communicating over the cellular network, the red LED (L1) on the unit’s circuitboard will be illuminat

27telephone number via the control panel PGM output. If after that the red trouble LED stays on steady,the LINKS is transmitting. If it doesn’t, the

28will be used to report a general trouble (which could be any of the trouble conditions described above) onthe LINKS1000.Note that the PC4010, PC4020

2LINKS1000 GLOSSARY OF TERMSThe following is a description of various terms used with regards to cellular technology.Electronic Serial Number (ESN)The

29002430 R0Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the productshall be free from defect

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meetscertain telecommunications network

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expresslyapproved by Digital Security Controls Ltd. could voidyour authority to use this

3INTRODUCING THE IMPORTANT NOTEA security system cannot prevent emergencies. It is only intended to alert you and, if included, a monitoringstation, o

4HOW THE LINKS1000 WORKSCellular CommunicationsAll cellular telephones, including the LINKS1000, must ‘register’ with the cellular network. ‘Registrat

5Upon completion of downloading, the LINKS1000 will ‘hang up’. The LINKS1000 will automatically disconnectany call after a 20 minute duration.Emergenc

6SETTING UP THE PROGRAMMERProgrammer Low Battery IndicationIf the Programmer’s batteries begin to run low, this message will be displayed:* PROGRAMMER

7Arranging for Cellular ServiceIn order for the LINKS1000 to communicate via the cellular telephone network, an account must be set up witha cellular

8Programming the LINKS1000Step 1.Programming the Cellular Telephone NumberScroll to “Write LINKS” and press [✱✱✱✱✱] to select. Scroll to “LINKS Phone