DSC PC2525 Manuel d'installation télécharger pdf (Page 12)

User Programming Commands

[

∗∗

∗

]+[5]+[Master Code]

The [

∗

][5] programming command allows the user to program Access Codes 2 through 8; the First Access

Code is the Master Code. The factory default for the Master Code is “1234”. The 8th Access Code may be

changed from a regular code to a One-Time Use Code by turning ON Zone Light 1 in Section [09]. The One-

Time Use code allows an individual, such as a service person, to disarm and then re-arm the system. After the

code is used, it is erased and will no longer work on the system.

NOTE: The One-Time Use code is only cleared when it is used to arm the system. If the Quick-Arm command

[

∗

][0] is used to arm, the One-Time Use code will not be erased.

Programming Access Codes:

Enter [

∗

][5][Master Code] to enter the Access Code Programming Mode; the “Program” light will begin to flash.

The Zone Lights are used to indicate the program status of the 8 Access Codes.

Zone Light Access Code Status

OFF Code not programmed

Steady Code programmed

Flashing Code being programmed

Upon entering this Programming Mode, the Zone Light 1 will be ON to indicate that the Master Code is

programmed with the Factory Default Code. The Master Code may be changed here or in Programming Section

[04] if the installer chooses to disable user-changing of the Master Code.

Changing or Adding a Code

To change Access Codes 1 to 8, press the corresponding key (1 to 8). The corresponding Zone Light will begin to

flash. Enter the new 4-digit number. Do not use the [

∗

] key or [#] key when entering the 4-digit number. After the

four digits are entered, the keypad will beep 3 times and the Zone Light will come on steady. If you are changing an

existing code, the new code will simply replace the old one. If you wish to program another code, press the number

key for the code to be programmed and enter the new 4-digit code. Press the [#] key to exit this section.

Erasing a Code

To erase a code, enter [

∗

][5][Master Code]. Press the key of the code you wish to erase. The Zone Light for that

code number will flash. Enter [

∗∗∗∗

NOTE: The Master Code cannot be erased. If the Master Code is forgotten and the panel is left disarmed,

program a new Master Code using the [

∗

][8][Installer’s Code][04] command or use the Second Master Code to

reprogram the Master Code. The Second Master Code is programmed using the [

∗

][8][Installer’s Code][05]

command or in Programming Section [05].

EEPROM Reset

If the Master Code is forgotten and the panel is armed, see Programming Section [99] for instructions on resetting

the panel to the factory default condition. Resetting the system is not necessary if the Second Master Code is

programmed. Refer to Programming Section [05] for information on using the Second Master Code.

User Function Commands

[

∗∗

∗

]+[6]+[Master Code]

This function is used to set the System Clock time and to set the Auto-Arm time as well as toggle a number of

system functions. As soon as the command is entered, the “Program” light will begin to flash. Enter [

∗

][6][Master

Code][Number from list below].

[1] System 24 Hr. Clock (Enter HH:MM)

[2] Auto-Arm Time (Enter HH:MM)

[3] Not Used

[4] Quick-Arm Enable/Disable

[5] Auto-Arm Enable/Disable

[6] Not Used

[7] Not Used

[8] System Test Function

[9] User Initiated Call-up

[0] Installer’s Test (This function will turn off automatically on arming.)

Items [4], [5] and [0] turn ON and OFF various features. When the item key is pressed and the feature is being

turned ON, the keypad sounder will beep 3 times. If the feature is being turned OFF the sounder will give one

long beep. Pressing item [8] gives a 2-second Bell / Siren and Keypad Light and Buzzer test.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 41 42

Commentaires sur ces manuels

Pas de commentaire

DSC PC2525 Manuel d'installation Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PC2525