DSC SYSTEM MASTER PC4000 Manuel d'instructions Page 12
- Page / 20
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10
7
USER FUNCTIONS COMMAND
[✱]+[6]+[ACCESS CODE]
Enter [✱][6][Access Code] and then use the [<][>] keys to display the items of the
function menu. Press [✱] to select an item.
[0]Quick Arm [1]Quick Exit [2]Auto Arm Control [3]Keypad Setup
[4]Bell/Comm Test [5]Door Chime [6]Spec. Messages [7]User Call Up
[8]View Partitions
Item [0], [1], [5] and [6] turn on and off various functions. To enable or disable these
functions, press the [✱] key to toggle “Y ”or “N” on the keypad.
Y - The function is enabled
N - The function is disabled
NOTE
: The Auto Arm time is a 24 hour clock and times must be entered as two digit
numbers.
E.g. HH - 01, 02,.....10,11,.....23,24
MM - 00, 01,.....35,36.....58,59
Enter 4 digits representing the time in hours and minutes (HH:MM) based on 24 hour
or military time. Always enter a leading zero where only one digit is required, 8:05 am
would be entered as 0805, 1:30 pm would be entered as 1330.
QUICK ARM
[✱]+[6]+[ACCESS CODE]+[0]
The “Quick Arm” feature is enabled by toggling to “Y” on the keypad. When enabled
the panel can be armed by entering [✱][0].
QUICK EXIT
[✱]+[6]+[ACCESS CODE]+[1]
The “Quick Exit” function is enabled by toggling to “Y” on the keypad. When enabled
the user can exit through any delay zone without altering the status of the system, by
entering [✱][0] on the keypad.
AUTO ARM CONTROL
[✱]+[6]+[ACCESS CODE]+[2]
The PC4000 can be programmed to arm a partition at the same time each day, by
enabling the Auto Arm function and programming the Auto Arm time.
At the selected Auto Arm time, the system will give a pre-alert. The keypad begins
to sound and the Bell/Siren will pulse once every 10 seconds to alert anyone on the
premises that the system is about to arm. The Bell/Siren pulse can be programmed
by the installer to be silent.
The keypad will sound for one minute before Auto Arming unless the Auto Arm is
aborted. To abort the Auto Arm and silence the keypad press any key during the
pre-alert. The Auto Arm will be attempted at the same time the following day. The
PC4000 can be programmed to require a code to be entered for a user to abort the
Auto Arm by the installer.
Upon selecting the Auto Arm Control function, the Auto Arm Control menu will
appear on the LCD keypad.
[0] Auto Arm [1] Auto Arm Time
Auto Arm toggles “Y” or “N” to enable or disable the Auto Arm function.
Auto Arm time is the time the partition will automatically arm itself every day.
ALARM MEMORY DISPLAY
[✱]+[3]
Press [✱] then [3] to enter the alarm memory mode. Any alarm caused during the
last armed period will be displayed. The “Alarm Memory” message will only be
displayed when an alarm occurred during the last armed period.
Press [#] to return to “READY”.
USER PROGRAMMING COMMANDS
[✱]+[5]+[MASTER CODE]
The [✱][5] Access Codes programming command is used to program additional
access codes of any type.
The PC4000 has 128 access codes. In the Installer’s Programming Section, these
codes can be divided up and assigned to partitions, or are turned into System
Master Codes, which have control over all partitions. This must be done before the
user can program the access code and the code type.
The first code is the System Grand Master Code. Only the Installer can change this
code, unless the Installer has enabled the user to change the System Grand Master.
There are 11 types of codes:
System Grand Master Code has no limitations to its use. It can create or delete
other System Master Codes or perform any other user feature the PC4000 user is
capable of doing. Only the first access code (Access Code 001) can be a System
Grand Master.
System Master Codes can do anything on the system. They can be used to
bypass, view memory, view trouble, etc. They may be used to create or delete any
type of code except for System Master Codes.
Partition Master Codes has unlimited access to their own partition. These types of
codes can create, delete or alter any code type in their partition other than System
Masters. They can only assign users to their own partition.
Arm/Disarm/Bypass Access Code may arm, disarm or bypass on the partition
to which it has been assigned.
Arm/Disarm Access Code can only be used to arm or disarm the partition to
which it has been assigned.
Arm Only Access Code can only arm the partition to which it has been assigned.
Door Strike Code can only activate [✱][7] utility output on the partition it belongs to if
the partition is disarmed.
Log Only Code will only put a record on to the event buffer.
Arm/Disarm/OTU Code is erased when used to arm.
Arm Only OTU Code is erased when used to arm.
Door Strike OTU Code is erased after used.
NOTE
: OTU stands for One Time Use.
- SYSTEM MASTER 1
- USER FUNCTIONS COMMAND 12
- ALARM MEMORY DISPLAY 12
- USER PROGRAMMING COMMANDS 12
- TROUBLE DISPLAY 13
- “AT-HOME” ARMING 14
- ZONE BYPASSING 14
- KEYPAD ZONES 16
- FAMILY ESCAPE PLANNING 16
- SYSTEM MASTER CODES 17
- MAINTENANCE 17
- LIMITED WARRANTY 17
- INTRODUCTION 18
- ABOUT YOUR SECURITY SYSTEM 18
- APPENDIX A 18
- DOC NOTICE 19
- FCC COMPLIANCE STATEMENT 19
- IMPORTANT INFORMATION 19
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC SYSTEM MASTER PC4000
(52 pages)
(40 pages)
(12 pages)Zanussi ZEM6740BBA podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Płyty grzewcze Zanussi ZEM6740BBA.
Dostarczamy 1 pdf podręczników Zanussi ZEM6740BBA do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels