DSC PC6010 Manuel d'installation télécharger pdf (Page 6)

SYSTEM AREASYSTEM AREA

SYSTEM AREA

SYSTEM OPTIONSSYSTEM OPTIONS

SYSTEM OPTIONS

SYS TOGGLE OPTSYS TOGGLE OPT

SYS TOGGLE OPT

System Options

This section contain options that are relevant to the entire system. System Toggle options, Keypad

Lockout options and System Times can all be programmed in this section.

Sys Toggle Options

Toggle options are in question form. Use the [*] key to toggle between Yes and No to enable or disable

the feature. Use the [<] [>] keys to scroll through the options.

60 Hz AC?

YES = The incoming AC power from the transformer cycles at 60 Hz. The North American

standard is 60 Hz.

NO = The incoming AC power cycles at 50 Hz.

Crystal Time Base?

YES = The timebase is the internal crystal oscillator.

NO = The timebase is the AC power input.

Timing for the clock in the PC6010 can come from two sources. The frequency of the AC power, or

a crystal oscillator on the circuit board. The default is to use the frequency of the incoming AC

because it is normally very stable. However, in some locations, the stability of the AC frequency is

less reliable. If this is the case then the crystal oscillator should be used.

Follows includes Alarms?

YES = Enables all outputs programmed to follow zones to also annunciate alarms when those zones

are armed.

When the zone is disarmed, the output will follow the zone status (i.e. when the zone is violated

the output will activate; when the zone is restored the output will deactivate).

When the zone is armed the output follows the zone’s alarm status (i.e. the output will not

activate until the zone is violated. The output remains active until a user clears the alarm

memory).

NO = Disables the ability to latch alarm status. The output only follows zone activity, whether the zone

is armed or disarmed.

Six digit access codes?

YES = All access codes on the system will be 6 digits in length, except for the DLS access code.

NO = Regular 4 digit codes to be used.

NOTE: When you change from 4-digit to 6-digit codes, you should use DLS-3 to upload the user codes,

and then perform a Duplicate Code and Card check. Please refer to the DLS-3 manual for more

information.

Keypad tamper enabled?

YES = Keypad Tampers are used. This option should be enabled only if keypad tamper plates are

attached to the keypad.

NO = Keypad Tampers are disabled.

Access Log On?

YES = The system will always make a log entry when it grants access to a user with an access card

NO = The system will not make a log entry when it grants access to a user with an access card, where

the user does not also enter an access code on the reader.

YES = The battery charging current will be 1.4A.

NO = The battery charging current will be 360mA.

Duplicate Code Check?

YES = The system will not allow the programming of duplicate user codes. If a user code is entered

that matches any of the other 1000 users, the Installer code, or any other user code (or the

Duress derivative of any code), the keypad will sound an error tone and the data will not be

saved.

NO = The system will allow duplicate user codes to be programmed.

ACCESS LOG ONACCESS LOG ON

ACCESS LOG ON

SYSTEM OPTIONSSYSTEM OPTIONS

SYSTEM OPTIONS

(01)(01)

(01)

SYS TOGGLE OPTSYS TOGGLE OPT

SYS TOGGLE OPT

(0)(0)

(0)

XTAL TIMEBASEXTAL TIMEBASE

XTAL TIMEBASE

6 DIGIT CODES6 DIGIT CODES

6 DIGIT CODES

KEYPAD TAMPERSKEYPAD TAMPERS

KEYPAD TAMPERS

FOLLOWS + ALARMSFOLLOWS + ALARMS

FOLLOWS + ALARMS

HI BATT CHARGHI BATT CHARG

HI BATT CHARG

60 HZ AC60 HZ AC

60 HZ AC

DUPLICATE CODEDUPLICATE CODE

DUPLICATE CODE

1 2 3 4 5 6 7 8 9 10 11 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

DSC PC6010 Manuel d'installation Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PC6010