DSC NT9005 V1.0 Spécifications télécharger pdf (Page 11)

Module Programming

[804]-[82-85] Zone Transmitter Supervision

Options

These eight bit toggle sections determine which wireless zones on

the system are supervised. All zones that are enabled will be super-

vised for communication integrity, and will operate according to the

zone type programmed.

☞

If a zone is disabled, it will not be supervised and zone

activity will be ignored by the panel. See section [202-

205].

Sub-

Section

Zone Enabled Disabled

[82] 01



02 



03 



04 



05 



06 



08 



[83] 09 



10 



11 



12 



14 



15 



16 



[84] 17 



18 



20 



21 



22 



24 



[85] 25 



26 



27 



28 



30 



31 



32 



[901] Installer Walk Test Enable/

Disable

[*]

Function

When this mode is ON, all zones become 24-Hr non force-armable

zones that will sound the bell (steady or pulsed ) for 2 seconds and

transmit their programmed alarm reporting codes (section [320-

323]) when violated. If the user attempts to arm while in Walk Test

the keypad will sound an error.

☞

Fire Troubles are not supported in Walk Test.

Alarm Memory is cleared upon entering Walk Test.

To Enable Walk Test Mode:

Disable ‘Keypad Blanking’ - section [016] option 3

Disable ‘Fire Bell is Continuous’ - section[016] option 8

Enter from normal state:

[*] [8] [Install Code] [2] [901]

To Disable Walk Test Mode:

Re-enter:[*] [8] [Install Code] [2] [901]

Re-enable ‘Keypad Blanking’ and ‘Fire Bell Continuous’ if

required.

☞

The User Walk Test ([*][6][8]) performs the same functions

as indicated here except that reporting codes are not trans-

mitted to the central station.

[902] Reset Module Supervision

All modules will automatically enroll within one minute upon

power-up. If modules are removed, enter this section to clear

any supervisory troubles that may be present. When this mode

is entered the system will attempt to re-enroll all modules.

☞

When this section is entered, all pending Supervisory Trouble

Restorals will not be logged or transmitted.

☞

If a module is NOT communicating properly with the system,

it will be deleted when you enter this section.

To Reset Module Supervision:

Enter from normal state:

[*] [8] [Install Code] [2] [902]

[903] Module Supervision Field

When this section is entered, the system will display all mod-

ules enrolled on the system.

[*] [8] [Install Code] [2] [903]

[904] Device Placement Test

FLASH

Device Selection - When this section is entered, a two digit entry is

required to select the zone number to be tested (01-32). If a device

is selected that is not enrolled, an error tone will sound.

Placement Indication - After the zone is selected the device sends

a signal to the NT9005 to register a signal strength value. These

results are indicated in the following table.

Indication LCD Bell/Buzzer

Good

Bad

Not Enrolled

Good

Bad

1 Beep/Squawk

3 Beep/Squawk

Error Tone

Chapter 2: Installation

2-1 Installation Procedure

Read the following procedure to familiarize yourself

with the necessary steps before installing the system.

1. Create a Layout - Draw a rough sketch of the

building and include all alarm detection devices,

modules and PGM output devices. Refer to the

following paragraphs for wiring requirements.

Keybus, Para 2-3.1

PGMs Para 2-3.2

Hardwired Zones Para 2-3.3

Telephone Line Wiring. Para 2-3.4

Battery and AC Wiring. Para 2-3.5

Refer to paragraph 2-4 and the associated instal-

lation sheets for placement of wireless detectors.

Locate the control panel in a dry area, near an

unswitched AC source and telephone line. Avoid

areas that are a possible source of electrical noise

such as computers, televisions, appliances, HVAC

systems. Avoid areas with large metal surfaces

such as heating ducts.

☞

Ensure that the control panel and other mod-

ules will be installed in an area that will be

protected by the system.

2. Mount Modules - Mount NT9204, Skyroute

modules as indicated in the associated installa-

tion manuals. Mount hardwired and PGM output

devices as required.

3. Route Wiring - Route the telephone line, AC

power line, PGM wiring, hardwired zone wiring

or Keybus wiring to the NT9005 panel location.

4. Install NT9005 Back Cover- Route wiring

through the access holes provided and mount the

back cover. Refer to paragraph 2.2 ‘NT9005

Installation’.

5. Complete Wiring - Connect the telephone line,

AC power line, PGM wiring, hardwired zone wir-

ing or Keybus wiring to the back cover.

6. Power up Control Panel - Connect the backup

battery. Place the unit on mounting plate ensur-

ing that the header on the printed circuit board

aligns with the terminal block on the back plate.

☞

The system will NOT power up if only the

battery is connected.

Ensure that the LCD display and buzzer are func-

tioning as described during the power up

sequence. See Start-up, paragragh 1-5.1.

7. Position and Enroll Wireless Detectors. This

can be performed in Flash Programming or sec-

tion [904] in Advanced Programming (placement

only). Refer to the Installation Sheets of wireless

devices to determine optimal placement. Mount

wireless devices after succesful placement. Refer

to appendices C, D and E

8. Program the System. The system can be quickly

programmed for basic setup in Flash Program-

ming or custom programmed manually in

Advanced Programming or with DLS-3 (down-

loading software) using a remote or local com-

puter. See Chap. 3: Programming.

9. Test the System. Two system tests are available:

the user Walk Test available in [*][6][8] program-

ming or the installer Walk Test described in sec-

tion [901] in Advanced Programming.

☞

In the User Walk Test report codes are not

sent to the central station.

2-2 NT9005 Installation

The NT9005 back cover comes attached to the back

of the NT9005 control unit. The back cover acts as a

mounting plate for the unit.

WWW.DIYALARMFORUM.COM

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 29 30

WWW.DIYALARMFORUM.COM 1

Commentaires sur ces manuels

Pas de commentaire

DSC NT9005 V1.0 Spécifications Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC NT9005 V1.0