DSC PC255O Spécifications télécharger pdf (Page 21)

Notes: The maximum delays allowed for UL

residential installations are: Entry delay = 45 seconds;

Exit delay = 60 seconds.

The maximum delays allowed for UL commercial

installations are: Entry delay = 60 seconds; Exit delay

= 60 seconds.

In UL commercial installations the bell cut-off time

shall be a minimum of 15 minutes.

[21] Auxiliary Delay Zone Times

This section requires 2 three digit entries to establish the

auxiliary entry and exit delay times. Do not press the [#] key

during data entry. The entry default time is 45 seconds and

may be changed to any time from ‘001’ second to ‘255’

seconds. The exit default time is 60 seconds and may be

changed to any time from ‘001’ second to ‘255’ seconds.

For the auxiliary delay times to be effective on a zone,

the zone must be set as type [7] in section [14] Zone

Definitions.

Note: The maximum delays for UL residential

installations are: Entry delay = 45 seconds Exit delay =

60 seconds.

For UL installations, swinger shutdown cannot be

enabled. Each alarm must be transmitted. As well, the

delay before transmission must not exceed 15 seconds.

[22] Communication Variables

Once this section is entered, 2 two digit numbers are

expected. Do not press the [#] key while entering data.

The first two digit number defines the number of alarm and

restoral pairs per zone that the communicator will make

before it shuts down for that zone. (Swinger shutdown).

The system will still go into a local alarm (Bell or siren)

unless section [18] light 8 is on to make the bell follow the

swinger shutdown counter. The counter may be reset

either when the panel is armed or on a 24 hour basis as

defined in the 3rd system option code, zone light 7. The

number of alarms may be programmed from ‘00’ to ‘99’

where ‘00’ means the communicator will never shutdown.

The fire zone cannot be shutdown, it always transmits.

The second two digit number defines the delay before

transmission. This delay is for zones defined as burglary

zones only. 24 hour zones or the fire zone will not be

delayed. The time may be programmed from ‘00’ to ‘99’

seconds where ‘00’ means no delay. If the system is

disarmed before the transmission delay expires, then no

transmission will take place.

[23] System Clock Times

After the section number [23] is entered, three 4 digit

numbers are expected. These numbers are the following

system times:

• Automatic arming time of day (HH:MM)

• For future use (99:99)

• Test transmission time of day (HH:MM)

Times are entered using the “24 hour clock” (military time).

Valid entries are 00 to 23 for HH (i.e. hours) and 00 to 59

for MM (i.e. minutes).

Note: IF INVALID TIMES ARE

ENTERED FUNCTIONS WILL NOT WORK. The

automatic arm function is enabled and disabled using

the [

✱

]+[6]+[Master Code] User’s Function Commands.

Auto-arm cannot be used for UL installations.

Light on= Keypad no buzzer on panic alarm

(See Keypad Zones.)

[7]*Light off= The [F]ire key is enabled

Light on= The [F]ire key is disabled

[8]*Light off= Disable bell shutdown

Light on= Enable bell shutdown

The bell will follow the swinger shutdown counter as set

in section [22].

* is default condition

[19] Zones 1 to 8 Bypass Mask

Use the same method of programming as used in section

[15]. Using this section it is possible to control which zones

the user is able to bypass using the [✱][1] command. If the

zone light is on the zone can be bypassed. If the zone light

is off that zone cannot be bypassed.

[20] System Times

Once the section number is entered, 6 two digit numbers

are expected to be entered. The valid range for entries in

this section is 01 to 99. Hex values or 00 are not allowed.

The times are entered in the following order:

• Entry delay time (in seconds)

• Exit delay time (in seconds)

• Bell cut-off time (in minutes)

• Delay before AC failure trouble reporting (in minutes)

• Slow zone response time (in 10 ms increments)

• Default zone response - 500 ms

• Test transmission/periodic download cycle time (in

days)

AC Failure Reporting Code is transmitted after the delay

programmed, which may be up to 99 minutes. The

reporting code for AC Failure Trouble is programmed in

sections [12] and [13].

The Zone Response Time is the length of time that an

alarm condition must be present on a zone before it is

detected. Certain vibration detectors, shock sensors and

glass break detectors require a fast response zone in

order to operate. The zones to which these types of

detectors are connected should be programmed as fast

response zones. All other zones should be programmed

as slow response zones. Zones are defined as either fast

or slow response time in section [14]. The fast response

time is fixed at 20 ms. The Slow Zone Response Time is

programmable in increments of 10 ms. The normal entry

would be 50 for a 500 ms slow response time.

A Test Transmission or a Periodic Download is sent to

the monitoring station on a regular basis to confirm that the

communication link to the system is intact. The test

transmission/periodic download cycle time is how often (in

days) the test transmission and /or periodic download is

sent. The reporting code for the test transmission is

programmed in section [12]. The time of day that the test

transmission and/or periodic download is sent is

programmed in section [23].

To enable either option, lights 7 and 8 in section [48]

must be programmed. If both test transmission and

periodic download are enabled, the same time will be

used for both. The test transmission will transmit first and

after it goes off line a periodic download will take place.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

DSC PC255O Spécifications Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PC255O