DSC Power8 PC5005 Guide de l'utilisateur télécharger pdf (Page 12)

Bell/Siren

Sounds After

Away Arming

Audible Exit Fault

In an attempt to reduce false alarms, the Audible Exit Fault is designed to notify you of an

improper exit when arming the system in the Away mode. In the event that you fail to exit

the premises during the allotted exit delay period, or if you do not securely close the Exit/

Entry door, the system will notify you that it was improperly armed in two ways: the keypad

will emit one continuous beep and the bell or siren will sound.

Your installer will tell you if this feature has been enabled on your system.

If this occurs:

1. Re-enter the premises.

2. Enter your [access code] to disarm the system. You must do this before the entry delay

timer expires.

3. Follow the Away arming procedure again, making sure to close the entry/exit door prop-

erly. (See “Away Arming” on page 7.)

Stay Arming Use the Stay arming method when you want to stay on the premises, but prevent unautho-

rized entry from outside the premises. The system will arm only the border (e.g., door and

window contacts) zones and will bypass the interior zones (e.g., motion detectors) so that

you will be free to move around inside.

1. Check that your system is ready to be armed (Ready light is ON)

2. Enter your [access code]. As you enter each digit, the keypad sounder beeps.

If you entered the access code incorrectly, the keypad sounder buzzes steadily for two

seconds. Re-enter your access code correctly.

When you enter a valid access code:

• The keypad sounds fast beeps.

• The Armed light turns ON.

• LCD5500Z keypads display “Exit Delay in Progress”.

• The exit delay begins and the keypad beeps once every second until the end of

the exit delay. The keypad beeps quickly for the last 10 seconds of the exit delay.

3. DO NOT exit the premises through the entry/exit door. This tells the system that you are

staying, and the system automatically bypasses the Stay/Away zones.

At the end of the exit delay, all keypad lights, except the Armed light, turn OFF.

LCD5500Z keypads display “System Armed in Stay Mode” and “Enter Code to Disarm

System”. At PC55XXZ and LCD5501Z keypads, the Bypass indicator will be on. The sys-

tem is now armed.

Setting the

Time and Date

You should make sure that your system has the correct time and date. This is important for

the auto-arm feature to function correctly, and for accurate reporting of events.

1. Press [Master Code] .

2. The keypad will now accept 10 consecutive digits:

• Enter the time in hours and minutes using the 24-hour format (00:00 to 23:59).

• Enter the date in months, days and years (MM DD YY).

4. To exit programming, press .

NOTE: If you have an LCD keypad, your installer may have programmed your sys-

tem to display the time and date while the keypad is idle. If this is the case, you can

press the key to clear the date and time display.

Changing the

LCD5500Z

Display

Language

You can change the language displayed on the LCD5500Z keypad.

1. Press and hold both of the keys together.

2. The keypad will enter Language Selection mode. Scroll to the language you want the

keypad to display.

3. To select a language and restart the keypad, press .

Changing

LCD5500Z

Display

Brightness/

Contrast

You can change the brightness and contrast of the LCD display on LCD5500Z keypads.

1. Press [Master code].

2. Use the keys to scroll to either Brightness Control or Contrast Control.

3. Press to select the setting you want to adjust.

4. A) ‘Brightness Control’: There are10 different backlighting levels. Use the keys

to scroll to the desired level.

B) ‘Contrast Control’: There are 10 different display contrast levels. Use the

keys to scroll to the desired contrast level.

5. To exit, press .

Changing

Keypad

Sounder

Loudness

You can select from 21 different keypad sounder tones for LCD and PC55XXZ keypads

From an LCD5500Z keypad:

1. Press [Master Code].

2. Use the keys to scroll to the message ‘Select Option <> Buzzer Control’.

3. Press to select.

4. Use the keys to scroll to the desired keypad sound level.

5. To exit, press .

From a PC55XXZ or LCD5501Z keypad:

Press and hold the key until the desired keypad sounder level is reached.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

DSC Power8 PC5005 Guide de l'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC Power8 PC5005