DSC PowerSeries Guide d'installation télécharger pdf (Page 26)

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [601] to [608] Additional Reporting Codes

Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to

Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable

the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting

event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt

to report an event if data [00] or data [FF] is programmed for the reporting code.

Section [681] to [688] Auto-Disarm Schedules

Program the time to auto-disarm (Section [681] for Partition 1, Section [682] for Partition 2 etc.) for each day of the week. Each Section has

seven, 4-digit entries, two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the military format (for

example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto disarming

Section [691] to [698] Auto-Disarm Holiday Schedule

Program the dates to be used for Auto-Disarm holiday schedule (Section [691] for Partition 1, Section [692] for Partition 2 etc.) Each Section

has fourteen, 6-digit entries, two digits for the month, two digits for the day and two digits for the year.The panel will not disarm on the pro-

grammed dates. The format of entering the date is MMDDYY. Program [99][99][99] to disable Auto-Disarm holiday schedule.

Section [700] Automatic Clock Adjust

Program the number of seconds for the last minute of the day. This can be used to make minor corrections to the clock if the AC frequency is

not reliable. Valid entries are [01] to [99].

Section [701] First International Option Code

Section [702] Second International Option Code

Option Description

[1] ON: configures the system for 50Hz AC. OFF: configures the system for 60Hz AC.

[2] ON: the system uses the internal crystal for the internal panel clock. OFF: the system uses the AC frequency for the internal panel clock.

[3] ON: the system will inhibit arming if a Low Battery or AC trouble condition is present. OFF: arming will not be inhibited.

[4] ON: all Tamper troubles will latch and arming will be inhibited. Enter Installer Programming to clear the trouble condition and return to

normal operation. OFF: tamper troubles will not latch and will not inhibit arming.

[5] ON: all access codes are 6 digits long. OFF: all access codes are 4 digits long.

[6] ON: the system will hang up if a busy tone is detected. This attempt is not counted towards the Maximum Dialing Attempts programmed.

OFF: the panel will not detect busy tones.

[7] ON: the system will charge the battery at approximately 700mA. OFF: the system will charge the battery at 400mA.

[8] ON: the system will abort a DLS session, Escort access, Listen In/Two-way session if a new central station communication event occurs.

OFF: non-critical events (Test transmission, Periodic Test and System Test) will not abort the session. Events will be communicated after

the session is complete.

Option Description

[1] ON: the communicator uses 33/67 make/break ratio when pulse dialing. OFF: the system uses 40/60 make/break ratio.

[2] ON: the system dials regardless of the presence of dial tone after the first attempt. OFF: the system dials only if dial tone is detected.

[3] ON: changes the Test Transmission Cycle Time to minutes. OFF: sends a Test Transmission after the programmed number of days.

[4] ON: the system accepts 1600Hz handshake pulse formats. OFF: the system accepts 1400Hz or 2300Hz handshakes.

[5] ON: the system generates a tone for 500mS every 2 seconds indicating digital equipment is making the call vs. a voice call.

OFF: the system does not generate a tone.

[6] ON: the tone generated (2100Hz.) indicates that digital equipment is making the call. OFF: the tone is 1300Hz.

[7] ON: the DLS down loading window is 1 hour. OFF: the DLS downloading window is 6 hours.

[8] ON: the system activates the bell output if a Failure to Communicate trouble occurs while the system is armed.

OFF: the system does NOT activate the bell output if a Failure to Communicate trouble occurs while the system is armed.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

DSC PowerSeries Guide d'installation Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PowerSeries