DSC PC255O Spécifications télécharger pdf (Page 20)

[1]*Light off= Communications are enabled

Light on= Communications are disabled

[2]*Light off = Restorals follow zones

Light on = Restorals sent on bell time out

[3]*Light off= No alarms are displayed while panel is armed

Light on = Alarms are displayed while panel is fully armed

[4]*Light off= Panel dials pulse (Rotary dialing)

Light on = Panel dials DTMF (Touch tone dialing)

[5]*Light off = Zones 1 to 8 use end-of-line-resistors

Light on = Zones 1 to 8 use normally closed zones

Note: For UL residential installations. When zones are

programmed as normally open (not supervised) they

shall be located within 3 feet of the control unit. Other

initiating circuits must be end-of-line supervised.

For UL commercial installations, zones must be end-of-

line supervised.

[6]*Light off= Keypad panic [P], bell is silent

Light on = Keypad panic [P], bell is audible

(See Keypad Zones.)

[7] Light off = Call 1st phone number with backup to 2nd

phone number if unsuccessful for 8 attempts

* Light on = Becomes call 1st phone number only

(See section [35].)

Note: Do not program backup to 2nd phone number

no 2nd phone number is programmed.

[8]* Light off= 16th code becomes normal access code

Light on = 16th code is maid's code (One Time Use code)

(Access codes are programmed with [✱][5] command)

* is default condition.

[16] 2nd System Option Code

Use same method of programming as used in section [15].

[1]*Light off = Partial closings not identified

Light on = Partial closings identified

(Bypassed zones will be identified with their alarm

transmissions between the partial closing code and the

closing code.)

[2]*Light off = Master code changeable

Light on = Master code changeable by installer

only

(See [✱]+[5] User’s Programming Commands page 9)

[3]*Light off = Disable bell squawk

Light on = Enabled bell squawk upon arm or disarm

(1 burst on Arm/2 bursts on Disarm)

[4]*Light off = PC16OUT module disabled

Light on = PC16OUT module enabled

(Module which provides 16 voltage outputs to indicate

panel conditions. See distributor for details.)

[5]*Light off = TLM trouble, audible bell when armed

Light on = TLM trouble only, armed or disarmed

(TLM = Telephone Line Monitoring)

[6]*Light off = Accepts 2300Hz (standard) handshake

Light on = Accepts 1400Hz handshake for Radionics

formats #3, 4, B and C in section [29]

(See Radionics format description page 21).

[7]*Light off = TLM enabled

Light on = TLM disabled

(TLM = Telephone Line Monitoring)

[8]*Light off = No access code required for zone bypassing

Light on = Use [✱]+[1]+[Access Code] for zone

bypassing (shunting)

* is default condition.

[17] 3rd System Option Code

[1]*Light off = Bell squawks once every 10 seconds during

auto-arm

Light on = Only the buzzer will sound during an auto-arm

(See Auto-arm, [✱]+[6]+[Master Code]+[2])

[2]*Light off = Acknowledge AC as a valid trouble

Light on = AC is excluded from trouble group

[3]*Light off = Zones are active on power up

Light on = 60 second bypass of zones on power up

[4]*Light off = Any key will abort the auto-arm

Light on = Auto-arm cancel requires a 4 digit access

code

(See Auto-arm, [✱]+[6]+[Master Code]+[2])

[5]*Light off = Home-Away zones act as interior zones when

active

Light on = Home-Away zones act as delay zones when

active

(See Zone Type 3, section [14].)

[6]*Light off = Auxiliary delay zones arm same as other

zones

Light on = Auxiliary delay zones can be force armed

(See Zone Type 7, section [14].)

[7]*Light off = Transmission counter for swinger shutdown

reset upon arming

Light on = Transmission counter reset every 24 hours at

midnight

(See section [22].)

[8]*Light off = Bypass status shown when disarmed only

Light on = Bypass status shown when armed or

disarmed

(See Zone Bypassing.)

* is default condition.

[18] 4th System Option Code

[1]*Light off= Quick exit disabled

Light on= Quick exit enabled ([✱]+[0] when armed)

(See Quick Exit.)

Note: Quick exit shall not be enabled on UL listed

systems.

[2]*Light off= Bell responds normally

Light on= Bell pulses always

(Bell pulses for fire or alarm)

[3]*Light off= Bypassed zones not displayed when armed

Light on = Bypassed zones displayed when armed

(See Zone Bypassing.)

[4]*Light off = Keypad LEDs always active

Light on = Keypad LEDs turn off after 2 minutes of no key

entry. Any alarm, entry delay, or keypress will

reactivate LEDs.

Note: This feature must not be used with an LCD

keypad.

[5]*Light off= Partial closing transmission on auto-arm

disabled

Light on= Partial closing transmission on auto-arm

enabled

(See Auto-arm, [✱]+[6]+[Master Code]+[2])

[6]*Light off= Keypad buzzer audible indication of panic

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

DSC PC255O Spécifications Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PC255O