DSC Power832 PC5O15 Manuel d'utilisateur télécharger pdf (Page 2)

FCC Compliance Statement:

CAUTION: Changes or modifications not expressly approved by Digital Secu-

rity Controls Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

‘ Re-orient the receiving antenna.

‘ Increase the separation between the equipment and receiver.

‘ Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

‘ Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: “How to Iden-

tify and Resolve Radio/Television Interference Problems”. This booklet is available

from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-

000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On the side of this

equipment is a label that contains, among other information, the FCC regis-

tration number of this equipment.

Notification to Telephone Company The customer shall notify the telephone

company of the particular line to which the connection will be made, and pro-

vide the FCC registration number and the ringer equivalence of the protective

circuit.

FCC Registration Number: F53CAN-34330-AL-E

Ringer Equivalence Number: 0.1B

USOC Jack: RJ-31X

Telephone Connection Requirements Except for the telephone company pro-

vided ringers, all connections to the telephone network shall be made through

standard plugs and telephone company provided jacks, or equivalent, in such a

manner as to allow for easy, immediate disconnection of the terminal equipment.

Standard jacks shall be so arranged that, if the plug connected thereto is with-

drawn, no interference to the operation of the equipment at the customer’s pre-

mises which remains connected to the telephone network shall occur by reason of

such withdrawal.

Incidence of Harm Should terminal equipment or protective circuitry cause harm

to the telephone network, the telephone company shall, where practicable, notify

the customer that temporary disconnection of service may be required; however,

where prior notice is not practicable, the telephone company may temporarily dis-

continue service if such action is deemed reasonable in the circumstances. In the

case of such temporary discontinuance, the telephone company shall promptly

notify the customer and will be given the opportunity to correct the situation.

Additional Telephone Company Information The security control panel must be

properly connected to the telephone line with a USOC RJ-31X telephone jack.

The FCC prohibits customer-provided terminal equipment be connected to party

lines or to be used in conjunction with coin telephone service. Interconnect rules

may vary from state to state.

Changes in Telephone Company Equipment or Facilities The telephone com-

pany may make changes in its communications facilities, equipment, operations

or procedures, where such actions are reasonably required and proper in its busi-

ness. Should any such changes render the customer’s terminal equipment incom-

patible with the telephone company facilities the customer shall be given

adequate notice to the effect modifications to maintain uninterrupted service.

Ringer Equivalence Number (REN) The REN is useful to determine the quantity

of devices that you may connect to your telephone line and still have all of those

devices ring when your telephone number is called. In most, but not all areas, the

sum of the RENs of all devices connected to one line should not exceed five (5.0).

To be certain of the number of devices that you may connect to your line, you may

want to contact your local telephone company.

Equipment Maintenance Facility If you experience trouble with this telephone

equipment, please contact the facility indicated below for information on obtaining

service or repairs. The telephone company may ask that you disconnect this

equipment from the network until the problem has been corrected or until you are

sure that the equipment is not malfunctioning.

Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094

Industry Canada Statement

AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette éti-

quette certifie que le matériel est conforme à certaines normes de protection,

d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada

n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le rac-

corder aux installations de l’entreprise locale de télécommunication. Le matériel

doit également être installé en suivant une méthode acceptée de raccordement.

L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions

énoncées ci-dessus n’empêchent pas la dégradation du service dans certaines sit-

uations.

Les réparations de matériel homologué doivent être effectuées par un centre

d’entretien canadien autorisé désigné par le fournisseur. La compagnie de télé-

communications peut demander à l’utilisateur de débrancher un appareil à la

suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la

terre de la source d’énergie électrique, les lignes téléphoniques et les canalisa-

tions d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est

particulièrement importante dans les régions rurales.

AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements lui-

même; il doit avoir recours à un service d’inspection des installations électriques, ou

à un électricien, selon le cas.

L’indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter

toute surcharge, le pourcentage de la charge totale qui peut être raccordée à un

circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé

peut être constituée de n’importe quelle combinaison de dispositifs, pourvu que la

somme des indices de charge de l’ensemble des dispositifs ne dépasse pas 100.

L’Indice de charge de ce produit est 0.1B.

NOTICE: The Industry Canada label identifies certified equipment. This certifica-

tion means that the equipment meets certain telecommunications network protec-

tive, operational and safety requirements. Industry Canada does not guarantee the

equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equip-

ment must also be installed using an acceptable method of connection. The cus-

tomer should be aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian main-

tenance facility designated by the supplier. Any repairs or alterations made by the

user to this equipment, or equipment malfunctions, may give the telecommunica-

tions company cause to request the user to disconnect the equipment.

User should ensure for their own protection that the electrical ground connections

of the power utility, telephone lines and internal metallic water pipe system, if

present, are connected together. This precaution may be particularly important in

rural areas.

CAUTION: Users should not attempt to make such connections themselves, but

should contact the appropriate electric inspection authority, or electrician, as

appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage

of the total load to be connected to a telephone loop which is used by the device,

to prevent overloading. The termination on a loop may consist of any combination

of devices subject only to the requirement that the total of the Load Numbers of all

the devices does not exceed 100.

The Load Number of this unit is 0.1B.

1 2 3 4 5 6 7 ... 41 42

Commentaires sur ces manuels

Pas de commentaire

DSC Power832 PC5O15 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC Power832 PC5O15