DSC WLS900 Instructions d'exploitation télécharger pdf (Page 16)

Press the -YES Key to end the test; this

message will be displayed. To continue testing,

press the

-YES Key. To enter the Installer’s

Programming Mode, press the

-NO Key.

During the Placement Test, the Sounders will

sound and one of the messages shown here will

be displayed. When “

Location GoodLocation Good

Location Good” is

indicated, the Sounder will sound a

single beepsingle beep

single beep.

When “

Location FairLocation Fair

Location Fair” is indicated, the Sounder

will sound

two beepstwo beeps

two beeps. When “

Location Location

Location

∗∗

∗

BAD BAD

BAD

∗∗

∗

” is indicated, the Sounder will sound

threethree

three

beepsbeeps

beeps.

Components must be mounted where “Good”

or “Fair” locations are indicated. If “Location

∗

BAD

∗

” is indicated, the component should be

relocated. In most cases, it may only be

necessary to move the component a short

distance from its originally intended location.

No sensor should be left in a location that tests

∗∗

∗

BAD

∗∗

∗

The First Sounder must be located where the test indicates “Location Good”.

After moving a component, repeat the test. If “Good” or “Fair” locations are indicated, repeat the Placement Test

at least once to confirm the location. When test results are satisfactory, scroll to the next component and perform

the Placement Test. When satisfactory test results have been received for all components, permanently mount the

components. Refer to “Mounting the Components” in Chapter 7 for mounting instructions.

After completing a Module Placement Test, you

must

arm and disarm the system. Be sure

to allow the exit delay to expire before disarming the system. If you do not arm and disarm

the system, zones may show as open the next time a supervisory transmission is sent

(every 12 minutes).

4 D: A Note About WLS904 Wireless Motion Detectors:

High Traffic Shutdown Mode

To prolong battery life, the motion detector uses a feature called High Traffic Shutdown. When motion is detected,

the device will transmit to the receiver and will then shut down for six minutes. If motion is detected again during

the first six minute shutdown time, the unit will reset the shutdown timer to three minutes. Each time the detector is

tripped during the shutdown time, the timer will be reset to three minutes again. The detector will thus remain in

the shut down mode until it does not detect motion for an entire six minute period.

The High Traffic Shutdown Mode affects testing the motion detector in two ways:

• When performing the

module placement testmodule placement test

module placement test, the unit must be tampered by removing the unit from the

backplate and replacing it. The placement test cannot be performed by creating motion in front of the device.

• When performing a

system testsystem test

system test, the unit must be left idle for six minutes before testing can be performed.

Once six minutes has passed, create motion in front of the detector to see if the device is both detecting

motion and transmitting to the receiver.

Motion Detector Transmission Delay

A motion detector transmission is always delayed by six seconds. This is necessary to prevent false alarms

caused by a motion sensor transmitting before a delay zone has a chance to report. This six-second delay cannot

be altered or disabled.

Walk Test Mode

The motion detector has a walk test mode which will activate an LED for testing purposes. To put the unit in the

walk test mode, create a tamper by removing the unit from the backplate and replacing it. For the next 90

seconds, the detector’s LED will turn on for three seconds every time motion is detected. During normal operation,

this LED will not turn on.

NOTE: The Walk Test Mode will override the High Traffic Shutdown Mode.

Chapter 4: Module Placement and Testing

The "ZONE LABEL" can

be any discription of up

to 16 letters, numbers,

spaces or ASCII

characters. See Section

6 for more information.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

DSC WLS900 Instructions d'exploitation Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC WLS900