DSC WLS900 Instructions d'exploitation télécharger pdf (Page 50)

Made and Printed in Canada

NOTICE: The Industry Canada label identifies certified equipment. This

certification means that the equipment meets certain telecommunications

network protective, operational and safety requirements. Industry Canada

does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to

be connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions

may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations

made by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the

equipment.

User should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines and internal metallic water

pipe system, if present, are connected together. This precaution may be

particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves,

but should contact the appropriate electric inspection authority, or electrician,

as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal

device provides an indication of the maximum number of terminals allowed

to be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the

sum of the Ringer Equivalence Number of all the devices does not exceed 5.

The REN of this unit is 0.1B.

AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué.

Cette étiquette certifie que le matériel est conforme à certaines normes de

protection, d’exploitation et de sécurité des réseaux de télécommunications.

Industrie Canada n’assure toutefois pas que le matériel fonctionnera à la

satisfaction de l’utilisateur.

This device complies with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause

undesired operation of the device.

Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le

document CNR-210. son utilisation est autorisée seulement aux conditions

suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif

doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage

est susceptible de compromettre le fonctionnement du dispositif.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le

raccorder aux installations de l’entreprise locale de télécommunication. Le

matériel doit également être installé en suivant une méthode acceptée de

raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité

aux conditions énoncées ci-dessus n’empêchent pas la dégradation du service

dans certaines situations.

Les réparations de matériel homologué doivent être effectuées par un centre

d’entretien canadien autorisé désigné par le fournisseur. La compagnie de

télécommunications peut demander à l’utilisateur de débrancher un appareil à la

suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la

terre de la source d’énergie électrique, les lignes téléphoniques et les

canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette

précaution est particulièrement importante dans les régions rurales.

AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements

lui-même; il doit avoir recours à un service d’inspection des installations

électriques, ou à un électricien, selon le cas.

AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif

terminal indique le nombre maximal de terminaux qui peuvent être raccordés à

une interface. La terminaison d’une interface téléphonique peut consister en une

combinaison de quelques dispositifs, à la seule condition que la somme d’indices

d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

L’indice d’équivalence de la sonnerie (IES) de ce produit est 0.1B.

CAUTION: Changes or modifications not expressly approved by Digital

Security Controls Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for

help.

The user may find the following booklet prepared by the FCC useful: “How

to Identify and Resolve Radio/Television Interference Problems”. This

booklet is available from the U.S. Government Printing Office, Washington

D.C. 20402, Stock # 004-000-00345-4

Important Information

This equipment complies with Part 68 of the FCC Rules. On the side of this

equipment is a label that contains, among other information, the FCC

registration number of this equipment.

Notification to Telephone Company

Upon request, the customer shall notify the telephone company of the

particular line to which the connection will be made, and provide the FCC

registration number and the ringer equivalence of the protective circuit.

FCC Registration Number: F53CAN-74834-AL-E

Ringer Equivalence Number: 0.1B

USOC Jack: RJ-31X or RJ-38X

Telephone Connection Requirements

Except for the telephone company provided ringers, all connections to the

telephone network shall be made through standard plugs and telephone

company provided jacks, or equivalent, in such a manner as to allow for

easy, immediate disconnection of the terminal equipment. Standard jacks

shall be so arranged that, if the plug connected thereto is withdrawn, no

interference to the operation of the equipment at the customer’s premises

FCC COMPLIANCE STATEMENT

which remains connected to the telephone network shall occur by reason

of such withdrawal.

Incidence of Harm

Should terminal equipment or protective circuitry cause harm to the

telephone network, the telephone company shall, where practicable, notify

the customer that temporary disconnection of service may be required;

however, where prior notice is not practicable, the telephone company

may temporarily discontinue service if such action is deemed reasonable

in the circumstances. In the case of such temporary discontinuance, the

telephone company shall promptly notify the customer and will be given the

opportunity to correct the situation.

Additional Telephone Company Information

The security Controller must be properly connected to the telephone line

with a USOC RJ-31X or RJ-38X telephone jack and a matching 8 pin

modular “Direct Connect Cord”.

The FCC prohibits customer-provided terminal equipment be connected to

party lines or to be used in conjunction with coin telephone service. Inter-

connect rules may vary from state to state.

Changes in Telephone Company Equipment of Facilities

The telephone company may make changes in its communications facilities,

equipment, operations or procedures, where such actions are reasonably

required and proper in its business. Should any such changes render the

customer’s terminal equipment incompatible with the telephone company

facilities the customer shall be given adequate notice to the effect

modifications to maintain uninterrupted service.

Ringer Equivalence Number (REN)

The REN is useful to determine the quantity of devices that you may

connect to your telephone line and still have all of those devices ring when

your telephone number is called. In most, but not all areas, the sum of the

RENs of all devices connected to one line should not exceed five (5.0). To

be certain of the number of devices that you may connect to your line, you

may want to contact your local telephone company.

Equipment Maintenance Facility

If you experience trouble with this telephone equipment, please contact the

facility indicated below for information on obtaining service or repairs. The

telephone company may ask that you disconnect this equipment from the

network until the problem has been corrected or until you are sure that the

equipment is not malfunctioning.

Digital Security Controls Ltd

160 Washburn Street

Lockport, New York, 14094

1 2 ... 45 46 47 48 49 50 51 52

Commentaires sur ces manuels

Pas de commentaire

DSC WLS900 Instructions d'exploitation Page 50

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC WLS900