DSC MAXSYS PC4020 Manuel d'installation Page 45
- Page / 52
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 16: Diagnostics and Troubleshooting
41
SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
battery trouble occurs, the panel will not restore the trou-
ble until it has been viewed using the [*][2] trouble dis-
play. The trouble will not be restore until it has been
viewed, even if the cause of the trouble has been physi-
cally restored. If the option if turned off, the panel will
restore these troubles as soon as the trouble condition is
physically restored. The option is off by default.
Trouble conditions can be transmitted to the central sta-
tion, if programmed (see Section 5.7 “Reporting Codes”).
To view trouble conditions, press the [*] key then [2]. The
keypad display will indicate the trouble. All possible
trouble displays and a description of each is listed below.
16.5System Fault Squawk
If the Sys.Flt.Squawk option is turned on, when the sys-
tem detects a zone tamper, zone fault or a module
tamper, all the burglary bell outputs will squawk once
every 5 seconds. The “squawks” will be silenced when
the alarm is silenced or a key is pressed on that partition.
By default this option is off.
Display Trouble Condition
Battery Trouble The battery connected to the control panel is low.
AC Trouble There is a power failure (keypad will be silent).
Aux Supply
Troub
The AUX, SAUX+ or PGM terminals on the alarm
control panel are overloaded
TLM Trouble There is a trouble with the telephone line.
TLM TBL Line #1 There is a trouble on telephone line 1 (only gener-
ated when using the PC4701 Fire Module).
TLM TBL Line #2 There is a trouble on telephone line 2 (only gener-
ated when using the PC4701 Fire Module).
FTC Trouble The alarm control panel can no longer communicate
with the central monitoring station. The trouble is
generated after the programmed failed communica-
tion attempts. If a later attempt to communicate is
successful, the trouble is cleared.
Bell CCT Trouble The bell circuit is open (PC4020 or PC4702).
Fire Trouble A fire loop is open circuit (indicated by the trouble
sound; cannot be silenced). If the alarm control
panel loses communication with any expansion mod-
ule, all Fire/Burglary outputs will activate once every
10 seconds until a keypress is made, or module com-
munication is restored.
2 Wire Smoke The fire zone on a PC4701 Fire Module is open. The
keypad will display “2-Wire Smoke” until the trouble
is restored.
Ground Fault The earth ground (EGND) connection is shorted to a
positive voltage source or shorted to a non-earth
ground potential.
Waterflow The Waterflow zone on a PC4701 Fire Module is
open. The keypad will display “Waterflow TBL” until
the zone trouble is restored.
Loss of Time This trouble is cleared when the system’s time and
date are reset.
Module Com
Fault
The panel has lost communications with a module.
Check to see if the module is connected properly,
then do a system reset. Only qualified service per-
sonnel can perform this function.
Combus Low
Pwr
Modules are not getting enough voltage from the
Combus. Check for proper connection of Combus, or
repower the Combus, if required. Only qualified ser-
vice personnel can perform this function.
4204 Battery TBL The battery connected to any PC4204 relay output
module is low (module number indicated in report-
ing code transmission and event buffer).
4204 AC Trouble A PC4204 relay output module loses incoming AC
power (keypad will be silent).
4204 AUX Trou-
ble
The Auxiliary supply on any PC4204 relay module is
overloaded.
Display Trouble Condition
LINKS Trouble A LINKS unit has one or more of the following trou-
ble conditions: loss of AC power, low battery, loss of
cellular communication or a tamper fault.
DLS Fault TBL The control panel has failed to complete communi-
cations with the downloading computer.
Device Fault A wireless zone has failed to report a zone supervi-
sory (press [*] to view which zone).
Device Low Batt A wireless zone has a low battery (press [*] to view
which zone/device).
Device Tamper A wireless zone has a tamper condition (press [*] to
view which zone).
Automation
Fault
The ESCORT4580 loses communication with the
Automation Output control module. If there is an
AC trouble present, the panel will not transmit the
Automation Fault reporting code to the central sta-
tion.
4820 Battery
Trouble
The battery connected to a PC4820 module is low.
4820 AC Trouble A PC4820 module has lost AC power.
4820 Lock Trou-
ble
A PC4820 module has a trouble with one of its lock-
ing devices. A lock trouble occurs when the lock
power output is overloaded or the lock power fuse
has failed.
4820 Aux Trou-
ble
The PC4820’s Auxiliary (AUX) supply is overloaded.
4820 Rdr Pw TBL A PC4820 module’s card reader power output is
overloaded or the reader power fuse has failed.
Smoke Low Sens A WLS906 Smoke Detector’s sensitivity is low.
4164 Signal Tbl Wireless zone transmissions are not being received
by the PC4164-RS wireless receiver.
RF Jam Detected Wireless device transmissions not being received by
the PC4164-RS wireless receiver
4702 AC TBL The PC4702 module has lost AC power.
4702 Battery TBL The battery connected to the PC4702 is low.
Bells Silenced Fire alarm signals have been silenced. Trouble will
clear when the system is reset (enter access code)
Insp. Test Active The fire inspector's test has been initiated. Trouble
will clear when the test mode is disabled.
Printer Off-Line The printer connected to the PC4400 module is off-
line.
PC4400 Trouble The DVAC line from central station is not present,
the module has failed internal diagnostics or DVAC
communications have been shut down.
- DLS-2 v1.3 1
- WARNING Please Read Carefully 2
- Table of Contents 3
- PC4020 Wiring Diagram 4
- Section 1: Introduction 5
- 2.1 Planning the System 6
- 2.2 Terminal Descriptions 6
- 2.5 Zone Wiring 8
- 2.6 Specialized Zone Wiring 9
- 2.8 AML Device Wiring 10
- DC) and can 11
- 2.14 Lithium Batteries 12
- Section 3: How to Program 13
- Section 4: Module Enrollment 15
- 4.3 Confirming Modules 16
- 4.4 Enrolling AML Devices 16
- 5.2 Creating Partitions 17
- 5.1 Zone Supervision 17
- 5.4 Zone Programming 18
- Section 6: Keypad Operation 22
- 6.4 Keypad Blanking 23
- 6.6 Keypad Lockout 23
- 6.7 Keypad Tampers 23
- 6.8 Alarm Memory Display 23
- 6.9 Zone Bypass Display 24
- 6.10 Function Key Programming 24
- 7.1 Installer’s Code 26
- 7.2 Other Access Codes 26
- 7.3 Guard Code 26
- 7.4 Access Code Options 26
- 7.5 Access Levels 27
- 8.2 Automatic Arming 28
- 10.1AC/DC Power Options 30
- 10.2Bell Circuit Supervision 30
- 10.3 Clock Options 30
- 10.4Event Messages 31
- 10.5Swinger Shutdown 31
- 10.6Tampers 31
- 10.8Test Transmissions 32
- 10.9Transmission Delay 32
- 10.11System Label 32
- 10.12Hourly Print 32
- 11.1Main Panel Outputs 33
- 11.3Output Pulse Times 35
- 12.1Telephone Numbers 36
- 12.2 Account Numbers 36
- 12.3Dialing Parameters 36
- 12.5Dialer Direction 38
- 12.6Communicator Formats 38
- 12.7Reporting Codes 39
- Section 13: Downloading 40
- Section 14: Event Scheduling 41
- 14.3Open/Close Suppression 42
- 16.1General Diagnostics 44
- 16.3Hardware Reset 44
- 16.5System Fault Squawk 45
- Appendix A: Reporting Codes 46
- Appendix C: ASCII Characters 49
- Limited Warranty 51
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC MAXSYS PC4020
(43 pages)
(32 pages)Zanussi ZEM6740BBA podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Płyty grzewcze Zanussi ZEM6740BBA.
Dostarczamy 1 pdf podręczników Zanussi ZEM6740BBA do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels