DSC PC6010 Manuel d'utilisateur télécharger pdf (Page 5)

Communicator

• Communicates using the SIA 1986, or the Contact ID format

• Communicates to up to three telephone numbers

• Each telephone number can be backed up by a LINKS1000

cellular communicator

• With the PC6442 and PC6443 modules, uses the Backbone

to communicate over a dedicated connection with alarm

presentation software. Communications are encrypted.

• One system and 32 area (account) codes

• Hexadecimal numbers available

• DTMF and pulse dialing

• True dial tone detect

Printer

• Can print data on a serial local printer using a PC6400 serial

interface module

Powerful 2.2 amp regulated power supply

• 776 mA auxiliary supply, 11.6 - 12.6 VDC, when charging a

36Ah battery.

• Separately fused for battery, auxiliary supply and bell output

• Electronic shutdown protection of the Combus

• Supervision for loss of AC power, low battery, electronic

shutdown of modules

• Internal clock locked to AC power frequency or optional

crystal time base

Battery

• 12 volt, 7 to 36Ah minimum rechargeable gel-cell or sealed

lead-acid battery

• Normal battery charging current 360mA

• High battery charging current (1.4A) available (software

selectable)

Transformer

• 16.5 VAC, 80VA

Output Voltage

Typically, with normal AC on and a fully charged battery, the

output voltage will be 13.8 VDC. With AC off and the battery

discharging, the voltage will go below 10 volts and then battery

cutoff will occur preventing further discharge. Devices that

require power from the control panel should be capable of

operation over the voltage range of 10 to 14 V

DC.

2 Enclosures

• PC4005C cabinet: PC6010 and two modules

• PC4003C cabinet: 2- PC6108A modules, 1 - PC6204 module,

1- PC6216 module, or 1 PC6400 module

2.2 Module Specifications

Refer to each module’s Installation Instruction sheet for wiring

and programming information.

PC6108A Expansion Module

• 8-zone expansion module

• Add up to 30 modules for a total of 256 zones on the system

• Supports double end-of-line zone loops (5600 ohm resistors)

• Connects to control panel via 4-wire Combus

• Nominal current draw of 30 mA (from Combus)

• AUX+ Output: 12 VDC, 250mA max. (power drawn from

Combus)

• Provides Tamper reporting codes

• Low Combus supervision

PC6204 High-Current Output Module

• 4 high-current outputs

• Output current 1A, 12VDC

• Up to 16 modules on system (up to 64 high-current outputs)

• Each output programmable for 1 of 56 options

• Connects to control panel via 4-wire Combus

• Low Combus supervision

• Four programmable relay contacts rated 2A, 30VDC

• Minimum 80 VA 16-18 volt transformer required

• Minimum 4 Ah battery required, up to 36Ah max.

• Current draw: 30 mA (from Combus)

• Provides Tamper and Trouble reporting codes

• AUX current: 500mA max.

• Tamper contact input

PC6216 Low Current Output Module

• 16-output low-current module

• Nominal current draw of 15 mA, plus power required by

outputs

• Output current 50mA, 12VDC

• Up to 9 modules on system

• Can be programmed as alarm or zone annunciators

• All 16 outputs can be programmed on each module, 1 of 56

options each

• Provides Tamper reporting codes

• Connects to control panel via 4-wire Combus

• Low Combus supervision

• Power drawn from Combus

PC6400 Serial (Printer) Module

• True RS-232 technology

• Handshake software switches

• DTR Protocol

• Baud rate: 4800

• Connects to control panel via 4-wire Combus

• Nominal current draw of 35 mA

• Low Combus supervision

• Tamper and Trouble reporting codes

• Maximum cable length: 200 feet (61 meters)

1 2 3 4 5 6 7 8 9 10 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

DSC PC6010 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC PC6010