DSC Power832 PC5O15 Manuel d'installation télécharger pdf (Page 26)

P R O G R A M D E S C R I P T I O N S

23

[09] 24 Hour Supervisory Zone If this zone is violated, whether armed or disarmed, the panel will report to the

central station, and log the zone fault. This zone gives a silent alarm by default.

Do not wirDo not wir

Do not wir

e 24-Hour Supere 24-Hour Super

e 24-Hour Super

visorvisor

visor

y zones on keypad zone tery zones on keypad zone ter

y zones on keypad zone ter

minals.minals.

minals.

[10] 24 Hour Supervisory Buzzer Zone Whether armed or disarmed, when this zone type is violated the panel will

immediately latch the keypad buzzer until a valid access code is entered and will communicate immediately to

the central station.

[11] 24 Hour Burglary Zone If this zone is violated, whether armed or disarmed, the panel will immediately latch

the alarm output and communicate to the central station. The alarm will sound for the Bell Cutoff time

programmed in

Section [005] “System Times”

or until a valid access code is entered.

[12]-[20] The following zone definitions operate similar to the 24 Hour Burglary except for System Event output type and

SIA identifier:

[12] 24 Hour Holdup Zone [15] 24 Hour Medical Zone [18] For future use

[13] 24 Hour Gas Zone [16] 24 Hour Panic Zone [19] 24 Hour Water Flow Zone

[14] 24 Hour Heat Zone [17] 24 Hour Emergency Zone [20] 24 Hour Freezer Zone

NOTES: [12] 24 Hour Holdup zones give a silent alarm by default.

Use fire zones for sprinklers.

[21] 24 Hour Latching Tamper If this zone is violated the installer must enter Installer Programming before the

panel will allow either Partition to be armed. The bell output will also activate for the programmed time and the

panel will communicate the alarm.

[22] Momentary Keyswitch Arm Zone Momentary violation of this zone will alternately arm/disarm the Partition the

zone is assigned to. This zone type should not be programmed as global.

[23] Maintained Keyswitch Arm Zone When this zone is violated, the partition it is assigned to will arm. When this

zone is secured, the partition will disarm. This zone should not be programmed as global zone.

Do not prDo not pr

Do not pr

ogram wirogram wir

ogram wir

eless zones as [21] or [22] Keyswitch or as [24] LINKS Answer zones.eless zones as [21] or [22] Keyswitch or as [24] LINKS Answer zones.

eless zones as [21] or [22] Keyswitch or as [24] LINKS Answer zones.

[24] LINKS Answer Zone If the LINKS1000 cellular communicator is being used it is possible to perform

downloading through the unit if the phone line is disconnected. If this is required connect the RING terminal of

the LINKS1000 to this zone. Refer to the LINKS1000 Installation sheet for more information.

Do not wirDo not wir

Do not wir

e LINKS Answer zones on keypad zone tere LINKS Answer zones on keypad zone ter

e LINKS Answer zones on keypad zone ter

minals.minals.

minals.

[25] Interior Delay Zone When the system is fully armed (ie. away armed), this zone will, as is standard, follow

the exit delay. It will also follow the entrance delay, provided that a delay zone is first tripped. If the delay

zone is not tripped first, a zone defined as “Interior Delay” will go into alarm instantly. When the system is

at-home or stay armed this zone will be active, but when it is tripped, it will initiate the entrance delay.

[26] 24 Hour Non-Alarm This zone type will be active at all times but will not cause an alarm.

This zone type shall not be used for Downlook-initiating zones (DLM-4L v1.0L) .This zone type shall not be used for Downlook-initiating zones (DLM-4L v1.0L) .

This zone type shall not be used for Downlook-initiating zones (DLM-4L v1.0L) .

[87] Delayed 24 Hour Fire (Wireless) This zone type operates the same as [07] Delayed 24 Hour Fire Zone and

must be used if the smoke detector is wireless.

[88] Standard 24 Hour Fire (Wireless) This zone type operates the same as [08] Standard 24 Hour Fire Zone and

must be used if the smoke detector is wireless.

5.1.1 Assigning Keypad Zones

Each keypad has a zone input to which a device—such as a door contact—can be connected. (See Section

2.12 “Keypad Zones” for wiring information.)

Once the keypad zones are installed, assign the zone in programming section [020] Keypad Zone

Assignments. Enter the 2 digit zone designated for each keypad (address) from 01-32.

Keypad Zone Assignments .................................... [020]

5.2 Zone Attributes

Each zone will operate according to the Zone Definition selected for it

(See Section 5.1 “Zone Definitions”)

.

Additional zone attributes can be programmed to customize the operation of a zone for a specific application.

The following attributes are programmable by zone:

Attributes for FirAttributes for Fir

Attributes for Fir

e Zones should not be changed fre Zones should not be changed fr

e Zones should not be changed fr

om default.om default.

om default.

Audible/Silent Determines whether the zone will activate the alarm output or will be silent.

Pulsed/Steady Determines if the alarm output will be steady or pulse on for 1 second and off for one second.

Activate Chime Determines if the zone will activate the chime feature

(See Section 3.4 “[

✱

] Commands, [

✱

] [4]

Door Chime ON/OFF”).

Bypass Enable Determines if the zone can be manually bypassed

(See Section 3.4 “[

✱

] Commands, [

✱

] [1] -

Zone Bypass”)

.

DSC Power832 PC5O15 Manuel d'installation Page 26

Commentaires sur ces manuels

DSC Power832 PC5O15 Manuel d'installation Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC Power832 PC5O15