DSC Power832 PC5O15 Manuel d'installation télécharger pdf (Page 33)

P R O G R A M D E S C R I P T I O N S

Please refer to the Control Panel Wiring Diagram in this manual for wiring instructions.

Only ONE of options [03] Sensor Reset, [04] 2-WOnly ONE of options [03] Sensor Reset, [04] 2-W

Only ONE of options [03] Sensor Reset, [04] 2-W

irir

e Smoke and [20] [e Smoke and [20] [

e Smoke and [20] [

✱

] [7] [2] Command Output] [7] [2] Command Output

] [7] [2] Command Output

Option #2 may be prOption #2 may be pr

Option #2 may be pr

ogrammed on the same system.ogrammed on the same system.

ogrammed on the same system.

[04] 2-Wire Smoke Support (PGM2 Only) PGM2 may be used in conjunction with two-wire smoke detectors.

PGM Output Attributes for PGM2 when used for 2-wirPGM Output Attributes for PGM2 when used for 2-wir

PGM Output Attributes for PGM2 when used for 2-wir

e smoke detector suppore smoke detector suppor

e smoke detector suppor

t must rt must r

t must r

emain at default,emain at default,

emain at default,

Attributes 1 and 3 ON.Attributes 1 and 3 ON.

Attributes 1 and 3 ON.

Do not prDo not pr

Do not pr

ogram any PGM output other than PGM2 for 2-wirogram any PGM output other than PGM2 for 2-wir

ogram any PGM output other than PGM2 for 2-wir

e smoke detector suppore smoke detector suppor

e smoke detector suppor

t.t.

Refer to the Hook-Up diagram in this manual for wiring instructions

(See Section 2.9.5 “Fire Zone Wiring - 2-Wire

Smoke Detectors”)

[05] Partition/System Armed Status The output will activate when the Partition or System is armed and

deactivate when disarmed.

[06] Ready Output The output will activate when the Partition or System is ready to arm. The output will

deactivate when the system is not secure or upon arming.

[07] Keypad Buzzer Follow The output will activate when any of the following events occur and will remain

active for as long as the keypad buzzer is active:

• Door Chime • Entry Delay • Audible Exit Delay

• Auto-Arm Prealert • 24 Hour Supervisory Buzzer Zone

[08] Courtesy Pulse Upon arming the output will activate for the duration of the exit delay plus two minutes. Upon

entry the PGM output will activate for the duration of the entry delay plus two minutes. If more than one courtesy pulse

output is required, they all must be programmed for global operation (PGM attributes 1 and 2 enabled).

[09] System Trouble Output The output will activate when any of the selected trouble conditions are present.

It will deactivate when all the selected trouble conditions are cleared.

The PGM attributes for this option, programmed in Sections [141] to [142], differ from the standard selection of

attributes. Program which trouble conditions will activate the output by selecting some or all of the following

attributes:

[1] .. Service Required [3] .. Telephone Line Trouble [6] .. Zone Tamper

(battery, bell, general trouble, [4] .. Failure to Communicate [7] .. Zone Low Battery

general tamper, general supervisory) [5] .. Fire Trouble / Zone Fault [8] .. Loss of Clock

[2] .. AC Failure

[10] Latched System Event (Strobe Output) The output will activate when any of the selected system events (alarms)

occur on the system. In the armed state, the output will deactivate only once the system is disarmed.

If an alarm activates this output in the disarmed state, the output will deactivate if a user enters a valid access

code while the Bell Cut-off timer is counting down. The output will also deactivate if someone arms the system

after the Bell Cut-off has expired. This output can be used to indicate that an alarm has occurred before entering

the premises.

The PGM attributes for this option, programmed in Sections [141] to [154], differ from the standard selection of

attributes. Program which events will activate the output by selecting some or all of the following attributes:

[1] ...... Burglary (Delay, Instant, Interior, Stay/Away and 24 Hour Burglary Zones)

[2] ...... Fire (Fire Keys, Fire Zones)

[3] ...... Panic (Panic Keys and Panic Zones)

[4] ...... Medical (Auxiliary Keys, Medical and Emergency Zones)

[5] ...... Supervisory (Supervisory, Freezer and Water Zones)

[6] ...... Priority (Gas, Heat, Sprinkler and 24 Hour Latching Zones)

[7] ...... Holdup (Holdup zones)

[8] ...... Output follows pulse timer (Section [164])

This output will activate for silent and audible alarThis output will activate for silent and audible alar

This output will activate for silent and audible alar

ms or medical conditions onlyms or medical conditions only

ms or medical conditions only

. It will not activate. It will not activate

. It will not activate

during prduring pr

during pr

e-alere-aler

e-aler

t or delays.t or delays.

t or delays.

[11] System Tamper

The output will activate when any Tamper condition is present and will deactivate when

all Tamper conditions are cleared.

[12] TLM and Alarm

The output will activate when a telephone line fault condition is present AND an alarm

occurs. The output will remain active until an access code is entered. The output will activate for both audible

and silent alarms if a TLM trouble is present.

This output will activate for all audible and silent alarThis output will activate for all audible and silent alar

This output will activate for all audible and silent alar

ms except Durms except Dur

ms except Dur

ess.ess.

ess.

[13] Kissoff The PGM Output will activate for two seconds after the panel receives the kissoff from the central station.

[14] Ground Start

The output will activate for two seconds before the panel attempts to dial to obtain dial tone

on Ground Start telephone equipment. Two second pauses should be inserted at the beginning of the phone

number when using this option.

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

DSC Power832 PC5O15 Manuel d'installation Page 33

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DSC Power832 PC5O15